Rotation Extrusion of Polyethylene Pipes with Different Diameters

Min NIE; Xiao-yang HU; Qi WANG

doi:10.14028/j.cnki.1003-3726.2015.02.007

您当前的位置：

首页 >

文章列表页 >

Rotation Extrusion of Polyethylene Pipes with Different Diameters

更新时间：2022-09-18

- Rotation Extrusion of Polyethylene Pipes with Different Diameters
- Polymer Bulletin Vol. 28, Issue 2, Pages: 47-51(2015)
- 作者机构：
  
  高分子材料工程国家重点实验室(四川大学)，四川大学高分子研究所，成都　610065
- 作者简介：
- 基金信息：
- DOI：10.14028/j.cnki.1003-3726.2015.02.007
  CLC：
- Published：2015-02，
  
  Received：26 May 2014，
  
  Revised：06 October 2014，
扫描看全文
Min NIE, Xiao-yang HU, Qi WANG. Rotation Extrusion of Polyethylene Pipes with Different Diameters. [J]. Polymer Bulletin 28(2):47-51(2015)
DOI：

Min NIE, Xiao-yang HU, Qi WANG. Rotation Extrusion of Polyethylene Pipes with Different Diameters. [J]. Polymer Bulletin 28(2):47-51(2015) DOI： 10.14028/j.cnki.1003-3726.2015.02.007.

摘要

通过口模旋转挤出制备3种管径聚乙烯(PE)管

系统研究其结构与性能.结果表明

相较于传统挤出PE管内串晶平行与轴向

旋转挤出过程中聚合物熔体的流动是轴向牵引流动和环向拖曳流动的叠加

其方向偏离轴向

可诱导串晶偏离轴向排列

从而提高PE管的环向取向度

实现PE管的环向增强

抑制裂纹在PE管内沿轴向扩展.随PE管管径的增加

在相同旋转角速度下环向流动线速度增大

串晶偏离轴向的夹角增加

环向取向度更高

因而旋转挤出制备的大口径PE管具有更优的性能。

Abstract

In this paper

polyethylene (PE) pipes with three diameters were prepared via die rotation extrusion and a thorough research was done on their microstructures and properties. The experimental results showed that compared to shish-kebab parallel to axial direction of PE pipe prepared by convention extrusion

hoop drag flow caused by die rotation was superimposed on axial traction flow during die rotation extrusion and the polymer flow direction was off the axial direction of the pipe so that the direction of shish-kebab alignment deviated from the axial direction to increase hoop orientation of the PE pipe and improve significantly the hoop strength and suppress the crack growth along the axial direction. With the increasing diameter of the PE pipe

hoop linear velocity went up at the same angular velocity and the angles of shish kebab deviated from the axial direction became larger so more improvement was achieved in the PE pipe with the longer diameter.

关键词

旋转挤出聚乙烯管形态串晶取向

Keywords

Rotation extrusionPolyethylene pipeMorphologyShish-kebabOrientation

references

更多指标>

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Preparation of High Performance Polyethylene Microtubes via Rotation Extrusion Processing

Progress in Processing Methods of Plastic Tubes

Mechanism of All Conjugated Polymer Phase Separation and Research Progress

Advances in Study of Ionic-aggregate Morphology of Ionomers

Research Progress on the Control over Microstructures and Properties of Ferroelectric Poly(vinylidene fluoride-trifluoroethylene)

Related Author

No data

Related Institution

State Key Laboratory of Polymer Materials Engineering, Polymer Research Institute of Sichuan University

State Key Laboratory of Polymer Materials Engineering, Polymer Research Institute of Sichuan University, Sichuan Provincial Engineering Laboratory of Plastic/Rubber Complex Processing Technology

State Key Laboratary of High Power Semiconductor Lasers,College of Science, Changchun University of Science and Technology

University of the Chinese Academy of Sciences

Hubei Provincial Key Laboratory of Green Materials for Light Industry, Hubei University of Technology

⁰