Preparation and Properties of Complex Treated Bamboo Fibers/PP Composites

Xin-huai GONG; Sheng-yun ZHAO; Rui-ye RAO; Liang-bi CHEN

doi:10.14028/j.cnki.1003-3726.2015.11.009

您当前的位置：

首页 >

文章列表页 >

Preparation and Properties of Complex Treated Bamboo Fibers/PP Composites

更新时间：2022-09-18

- Preparation and Properties of Complex Treated Bamboo Fibers/PP Composites
- Polymer Bulletin Vol. 28, Issue 11, Pages: 64-70(2015)
- 作者机构：
  
  1.武夷学院生态与资源工程学院，武夷山　354300
  2.闽北竹产业公共技术创新服务平台，武夷山　354300
  3.绿色化工技术福建省高校重点实验室，武夷山　354300
- 作者简介：
- 基金信息：
- DOI：10.14028/j.cnki.1003-3726.2015.11.009
  CLC：
- Published：2015-11，
  
  Received：29 December 2014，
  
  Revised：09 May 2015，
扫描看全文
Xin-huai GONG, Sheng-yun ZHAO, Rui-ye RAO, Liang-bi CHEN. Preparation and Properties of Complex Treated Bamboo Fibers/PP Composites. [J]. Polymer Bulletin 28(11):64-70(2015)
DOI：

Xin-huai GONG, Sheng-yun ZHAO, Rui-ye RAO, Liang-bi CHEN. Preparation and Properties of Complex Treated Bamboo Fibers/PP Composites. [J]. Polymer Bulletin 28(11):64-70(2015) DOI： 10.14028/j.cnki.1003-3726.2015.11.009.

摘要

为改善竹纤维(BF)与聚丙烯(PP)的界面结合

采用碱(NaOH)和异氰酸酯偶联剂(TDI)复合改性竹纤维

制备BF/PP复合材料.分析了竹纤维改性前后主要化学成分、热行为及化学结构变化

考察了竹纤维改性对复合材料维卡软化点(VSP)和动态热力学性能影响

用扫描电镜对复合材料断面进行了观察

最后探讨了改性竹纤维添加量对复合材料力学性能的影响.结果表明:BF经复合改性后

表面形成了氨酯键结构

竹纤维素晶体尺寸和结晶度增大

竹纤维的最快热降解温度和复合材料的VSP分别提高了20℃和4.5℃.SEM、DMA分析显示

竹纤维复合改性改善了两相界面结合

利于力学性能提高.拉伸实验表明

在复合改性竹纤维添加比例为40%时

复合材料综合性能最佳

其冲击强度、拉伸强度和弯曲强度分别增加了21.6%、23.3%和27.8%

拉伸模量和弯曲模量分别增加了24.2%和30.4%。

Abstract

Bamboo fiber(BF) was modified with alkali(NaOH) treatment + isocyanate(TDI) treatment to improve the interfacial adhesion of BF/PP composites. The content of the main components were measured

the chemical structures and thermal properties of BF were studied

the mechanical properties

thermal properties and dynamic properties of the composites were investigated

the morphology of fractured composite surfaces were observed by scaning electron microscopy(SEM)

and effects of modified BF loading rate on mechanical properties of the composites were also analyzed. The results showed that there formed amine ester bond and showed an increase in width of crystal region and relative crystallinity of BF after complex treatments of NaOH + TDI

the fastest thermal degradation temperature and vicat softing point of the composites were increased by 20℃ and 4.5℃ respectively. The results of dynamic mechanical analysis(DMA) showed that the peak value of tanδ decreased after complex modification. SEM observation revealed that the interfacial adhesion between BF and PP was improved by complex treatment of NaOH + TDI. When BF loading rate was 40%

the comprehensive properties of the composite performed the best

the impact strength

tensile strength and bending strength of the composite were increased by 21.6%

23.3% and 27.8% respectively

the tensile modulus and flexural modulus were increased by 24.2% and 30.4% respectively.

关键词

竹纤维界面改性聚丙烯竹塑复合材料

Keywords

Bamboo fiberInterface modificationPolypropyleneBamboo plastic composite

references

更多指标>

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Influences of Polypropylene on Phase II-I Transformation of Polybutene-1

Progress in β-Nucleating Agent for Polypropylene

Connecting the Knowledge in Polymer Physics through the Comprehensive Experimental Teaching Design of Polypropylene Foaming Materials

Case Teaching of Polymer Physics Based on the Technology of Preparing Lithium-ion Battery Separator of Polypropylene

Research Progress of Special Resin for Thin-wall Injection Molding Polypropylene

Related Author

No data

Related Institution

Shandong Provincial Key Laboratory of Olefin Catalysis and Polymerization, Key Laboratory of Rubber-Plastics (Ministry of Education), School of Polymer Science and Engineering, Qingdao University of Science and Technology

Beijing National Laboratory for Molecular Science, CAS Key Laboratory of Engineering Plastics, Institute of Chemistry, Chinese Academy of Sciences

Chongqing School, University of Chinese Academy of Sciences

Chongqing Institute of Green and Intelligent Technology, Chinese Academy of Sciences

College of Materials Science and Engineering, Chongqing University of Technology

⁰